DLF The Arbour Sector 63 Kitchen Planning Guide
DLF The Arbour Sector 63 kitchen planning: treat amendment workflow as context, not possession; verify drawings, measurements and current fit-out rules.
- Kautuk Sahni
- 9 min read
DLF The Arbour Sector 63 Kitchen Planning Guide
For DLF The Arbour, a safe modular-kitchen plan starts by matching the owner’s exact project phase, then verifying handover evidence, current fit-out access and finished-site dimensions. WoodAge is a Gurugram-based custom furniture manufacturer founded in 2003; this guide is a planning resource, not proof that WoodAge has completed work in this project.
Evidence boundary - verified 28 July 2026: An HRERA registration, extension, amendment, completion date or projected OC/CC does not by itself prove possession, keys, utilities, snag closure or permission to start interiors. WoodAge does not claim a project or client relationship with DLF The Arbour.
Official evidence for DLF The Arbour
| Record/phase | Official reference | Status shown by official source | Date type shown |
|---|---|---|---|
| Amendment record | RERA-GRG-1911-2025 | Approved and ready for certificate-issuing process on the amendment record | No possession or completion date asserted |
How to interpret it: An amendment workflow is not proof of possession, interior access, ceiling height or society rules. Use it only as project-context evidence and recheck the live record before any status statement. Open the official HRERA source. The downloadable WoodAge Gurugram project-phase watchlist and its methodology preserve the source/date boundary.
Five evidence stages before factory production
| Stage | What the owner can safely do | What must remain open |
|---|---|---|
| Project record only | List storage needs, appliance categories, finish preferences and budget structure | Possession, access, final layout and production date |
| Applicable OC/CC/PCC or handover evidence | Match the certificate/letter to phase, tower and unit | Finished dimensions and snag-dependent work |
| Keys and current management circular | Confirm contractor documents, lift route, unloading, work hours and waste rules | Cabinet sizes until site survey |
| Physical site measurement | Record walls, levels, openings, plumbing, electrical load/points, exhaust route and appliance clearances | Production until drawings/BOQ are signed |
| Signed drawings and BOQ | Release named materials, thicknesses, finishes, hardware lines, quantities, inclusions and exclusions | Any variation not approved in writing |
A marketing plan or sale-agreement drawing can start a concept. It should not release cabinet cutting because plaster, tiles, shafts, counters and service points can change usable dimensions.
Project and locality context
Project: DLF The Arbour Location: Sector 63, Gurugram Corridor: Golf Course Extension Road
Sector 63 is served through the Golf Course Extension Road side of Gurugram. Use locality only for service planning; exact lift, unloading, working-hour and contractor requirements must come from the current project circular. WoodAge’s Dwarka Expressway modular kitchen page explains the wider service context where relevant; it does not replace project documents.
Project facts to re-check (21 August 2026)
WoodAge does not claim a completed project at DLF The Arbour. These dated DLF and regulator facts are planning references; re-confirm the tower, delivered floor plan, MEP points, management rules, lift slots and work hours before design or dispatch.
| Dated fact | Primary source | Kitchen-planning implication |
|---|---|---|
| DLF identifies The Arbour in Sector 63, Gurugram. | DLF The Arbour compliance page | Record Sector 63, tower and unit on the survey sheet; locality does not define the plan. |
DLF’s compliance page lists RERA RC/REP/HARERA/GGM/671/403/2023/15. | DLF The Arbour compliance page, HRERA project record | Use the registered project identity to select the correct current drawing. |
| The compliance page links zoning, building-plan and other approval documents. | DLF The Arbour compliance page | Approval documents are the place to verify plan revision, not a sales image. |
| DLF’s compliance wording identifies construction as started. | DLF The Arbour compliance page | “Construction Started” does not establish a unit’s possession, finished MEP points or interior access. |
| The registered scope is marketed as 4 BR plus utility units. | DLF The Arbour compliance page | Ask for the exact 4 BR + utility plan and keep utility-room service points separate from the kitchen BOQ. |
| DLF’s 360-view page labels views as reference-only. | DLF The Arbour 360 view | Do not measure walls, openings or ceiling interfaces from a rendered view. |
The Arbour document-delta check before cabinet release
The Arbour compliance page records both an addendum and later revised approvals. For a 4 BR + utility kitchen, that is a reason to maintain a document delta instead of relying on an old marketing plan.
| Document delta | Official record | Buyer/design action |
|---|---|---|
| Registered identity | DLF’s Arbour compliance page names The Arbour and RERA RC/REP/HARERA/GGM/671/403/2023/15. | Copy the registration, tower and unit from the agreement into the survey packet. |
| Unit type/count | DLF lists 1,137 4 BR + Utility units. | Confirm the exact 4 BR + Utility plan; a project count cannot determine the kitchen wall or service spine. |
| Registration addendum | The page lists an addendum dated 1 May 2025. | Record which registration version the agreement and latest plan refer to. |
| Site/building approvals | DLF lists zoning approval and building/site plan approval, plus earlier approved plans. | Compare the latest approved plan to the owner’s signed plan before setting cabinet lengths or openings. |
| Revised drawings | The page lists revised building plans from 2024, including basement, elevation and floor/area material. | Ask for the relevant tower/floor drawing and keep its date; do not use a generic 360 view as as-built evidence. |
| Environmental/fire trail | DLF lists fire-scheme approval and revised environment/compliance entries on the compliance page. | Treat these as project approvals; still obtain live management, exhaust and electrical permissions. |
| Site-status evidence | DLF publishes dated site photographs through July 2026 and a construction-status document heading. | Use the latest record for context, then verify owner access, keys and current finished condition. |
| Logistics fields | Compliance identifies parking rights and project consultants, but not a unit’s active goods-lift slot. | Measure the door/lift route and attach the current facility circular before dispatch. |
Source boundary: DLF’s compliance record supports the registered project and approval/document trail. It does not establish an individual unit’s possession, as-built kitchen, dimensions, work hours or modification permission.
DLF The Arbour questions before a kitchen layout
| Question to answer | Evidence to collect | Why it changes the design |
|---|---|---|
| Which tower, stack and 4 BR + utility plan applies to the unit? | Allotment, latest DLF plan and tower identifier | Prevents a different stack or utility layout from becoming the BOQ basis. |
| Does the utility room share a shaft, drain or electrical route with the kitchen? | Signed plan plus measured sink, waste, DB and exhaust points | Controls wet-zone separation and appliance planning. |
| Which approval/floor-plan revision is current, and has the unit reached handover access? | DLF compliance documents plus owner-specific handover evidence | Separates construction status from production readiness. |
| What lift, unloading and contractor rule applies to The Arbour today? | Dated management/facility circular and lift measurements | Controls panel packaging, protection and installation sequence. |
Site-measurement sheet for this kitchen
Measure and photograph each item against a numbered wall/elevation:
| Measurement/evidence | Why it changes the kitchen |
|---|---|
| Finished wall-to-wall width at floor, counter and wall-unit height | Reveals taper and prevents relying on one width |
| Floor and wall level/plumb | Determines fillers, scribes and counter support |
| Door/window/opening size and swing | Protects shutters, drawers and circulation |
| Sink inlet, waste and floor-trap position | Controls wet-zone cabinet and maintenance access |
| Hob/chimney position and exhaust route | Controls wall units, duct path and service clearance |
| Electrical points, circuit/load information and DB route | Appliance requirements must be checked by a qualified electrician |
| Appliance model sheets | Cut-outs and ventilation differ by exact model |
| Counter/backsplash condition | Decides whether work is cabinet-only or includes counter/civil scope |
| Existing carcass moisture, swelling, sag and fixing condition | Supports retain/repair/replace decisions |
| Lift, doorway and material route dimensions | Prevents transport/installation assumptions |
Do not publish or quote a project-wide kitchen size from one unit. Tower, stack, unit revision and site finish can differ.
Material and finish evidence to attach to the BOQ
Use the room and failure mode, not a society name, to choose materials:
- For board products, record brand, product line, thickness, relevant IS/ISI/CML marking where applicable, invoice description and wet/dry-zone use. The BWP plywood vs HDHMR vs MDF guide explains what the standards do and do not establish.
- For laminate, acrylic, PU or veneer, name the substrate, finish/product code, edge process, cleaning limits, repair route and written warranty. See the kitchen finish comparison.
- For hinges, slides and lift systems, list the manufacturer, exact product line, quantity and load/use class instead of writing only “premium hardware”.
- For appliances, attach the final manufacturer drawing before closing cabinet dimensions.
There is no honest universal installed lifespan for a DLF The Arbour kitchen. Water exposure, workmanship, edge protection, loading, maintenance and product-specific warranties vary.
Existing kitchen: retain, repair or replace
If a kitchen already exists, decide cabinet by cabinet:
- Retain only when the carcass is dry, square, well fixed and compatible with the intended hardware/finish.
- Repair when damage is isolated and a written repair scope can restore the edge, back, hinge plate or shelf without hiding moisture damage.
- Replace when swelling, delamination, persistent leakage, sagging, failed fixings or a fundamentally incompatible layout makes retention unreliable.
Photograph rejected components and state the decision in the BOQ. Project age or brand is not a substitute for inspection.
Society access and logistics
Ask the current management/RWA/facility team for a dated written circular. Confirm contractor registration, identity documents, insurance if required, refundable/non-refundable charges, work hours, noisy-work limits, lift booking/protection, unloading point, debris route and restrictions on plumbing/electrical/structural work. This page asserts no DLF The Arbour NOC duration, deposit or working window because these can change.
When should planning and production start?
- Before handover: finalise needs, evidence standards, appliance shortlist and a comparable BOQ format.
- After owner-specific handover/access: inspect services, snags and any existing cabinets; obtain the current management circular.
- After finished-site measurement: create elevations and service coordination drawings.
- After written approval: release production against a versioned drawing set and BOQ.
For quote comparison, use WoodAge’s modular kitchen quotation guide so exclusions do not masquerade as savings.
Questions owners ask
Does the DLF The Arbour amendment record mean the unit is ready for interiors?
No. Readiness needs owner-specific handover/keys, applicable certificates, snag closure, utilities, site measurement and current access rules.
Can WoodAge confirm my possession or society rules?
No. Confirm possession/handover with the developer and owner documents, official status with HRERA, and current fit-out rules with project management/RWA. WoodAge can use those documents for cabinetry planning.
Can a kitchen be quoted from the floor plan alone?
A plan can support a provisional scope. A production BOQ needs finished-site measurements, service positions, appliance models and access constraints. Label any pre-measurement amount as an estimate with inclusions/exclusions.
Does this page prove WoodAge has clients in DLF The Arbour?
No. The page targets a project-specific planning query and cites public records. A WoodAge relationship would require permission-cleared first-party evidence and is not claimed here.
What should I bring to a WoodAge planning discussion?
Bring the agreement/allotment page showing the project ID and phase, tower/unit reference, applicable handover/certificate documents, dimensioned plan, current fit-out circular, site photos, appliance shortlist and any existing-kitchen inspection notes.
Source and update method
Primary project-status source: Haryana RERA record for DLF The Arbour. Status was checked on 28 July 2026. Recheck the live record and owner-specific documents before acting because registrations, extensions, amendments and certificate links can change.
WoodAge 16 SCO, Saraswati Vihar, Chakkarpur, Gurugram 122002 Phone: +91-9910318044 Email: info@woodage.in
Last evidence review: 28 July 2026. Final material, price, timeline and layout depend on site measurement, product evidence, current access rules and a signed BOQ.